XCR Factory (and Custom) Port Specs - Page 3
Like Tree1Likes
Page 3 of 3 FirstFirst 123
Results 21 to 26 of 26

Thread: XCR Factory (and Custom) Port Specs

  1. #21
    XCR Guru Sean K.'s Avatar
    Join Date
    Nov 2008
    Location
    AZ
    Posts
    21,720
    Quote Originally Posted by navalbeaver View Post
    Are talking about the latest one I sent you? I think I held onto that one because it was one of the few type 3s that would actually turn off the gas on "0". There was a thread way back where I noticed the detents and the gas dial ports weren't lined up. Is that what your'e talking about?

    https://www.xcrforum.com/forum/15-fi...ays-off-3.html
    It is the latest one you sent, but I haven't looked to see if the detents and ports lined up. I hope that doesn't mean it's going to have cycling problems on super sonics since the ports don't line up
    "Necessity is the plea for every infringement of human liberty. It is the argument of tyrants; the creed of slaves."-William Pitt the Younger

  2. #22
    XCR Guru navalbeaver's Avatar
    Join Date
    Jan 2010
    Location
    Redneck Riviera
    Posts
    2,355
    Quote Originally Posted by Sean K. View Post
    It is the latest one you sent, but I haven't looked to see if the detents and ports lined up. I hope that doesn't mean it's going to have cycling problems on super sonics since the ports don't line up
    I think they do line up because I kept it because the ones that lined up suppress better.

  3. #23
    XCR Guru Sean K.'s Avatar
    Join Date
    Nov 2008
    Location
    AZ
    Posts
    21,720
    Quote Originally Posted by navalbeaver View Post
    I think they do line up because I kept it because the ones that lined up suppress better.
    Shoot. I wish you hadn't sent it to me if you wanted it for suppressed. Worse yet, I already modded it....so it wouldn't do any good to send it back (Unless you needed more gas on the higher settings).

    If you want it though...let me know.
    "Necessity is the plea for every infringement of human liberty. It is the argument of tyrants; the creed of slaves."-William Pitt the Younger

  4. Remove Advertisements
    XCRForum.com
    Advertisements
     

  5. #24
    XCR Guru navalbeaver's Avatar
    Join Date
    Jan 2010
    Location
    Redneck Riviera
    Posts
    2,355
    Quote Originally Posted by Sean K. View Post
    Shoot. I wish you hadn't sent it to me if you wanted it for suppressed. Worse yet, I already modded it....so it wouldn't do any good to send it back (Unless you needed more gas on the higher settings).

    If you want it though...let me know.
    It's not a problem. Wouldn't have let it go if I needed it. I've been tinkering with the type 0 and 2s lately anyway
    Sean K. likes this.

  6. #25
    XCR Guru Sean K.'s Avatar
    Join Date
    Nov 2008
    Location
    AZ
    Posts
    21,720
    JFYI Nate,

    Zero did NOT turn off the gas. Gun ran really well on zero with supers....55 gr. IMI M193.


    You were right....no need to open any of the ports. It was chucking brass hard AF and 30' or more on setting 2. It was odd that it was throwing it 4-5 o'clock rather than forward or 3 o'clock.
    Last edited by Sean K.; 11-27-2019 at 12:27 PM.
    "Necessity is the plea for every infringement of human liberty. It is the argument of tyrants; the creed of slaves."-William Pitt the Younger

  7. #26
    XCR Guru Sean K.'s Avatar
    Join Date
    Nov 2008
    Location
    AZ
    Posts
    21,720
    Stock from Rob Arms Type 3 Dial Port Sizes in 6.5G with 11" bbl:

    7=.082"
    6=.076
    5=.070
    4=.067
    3=.064

    I don't have calibrated gauge pins for the smaller sizes....drill bit wise they are apparently smaller than .040 thou.


    I believe this is the wrong dial for this caliber (or just as likely....the bbl length since it's already 15 thou bigger than the "small hole" dial in post #15). I'll have to contact RA to verify.


    Bbl port is ~.078" currently....it will take both a .081 and .082 gauge pin in the beginning of the hole, but won't go all the way through.

    Gas block port is .125".

    ***EDIT***Drilled my bbl port to .082"....hopefully that will help with the bolt over base malfunctions I've been having and the bolt not locking back on empty. Not super concerned about erratic ejection unless it's so weak that it might get stuck in the port.
    Last edited by Sean K.; 04-24-2020 at 05:36 PM.
    "Necessity is the plea for every infringement of human liberty. It is the argument of tyrants; the creed of slaves."-William Pitt the Younger

Page 3 of 3 FirstFirst 123

Sponsors

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. WTB factory fixed stock, factory folder and old style trigger too
    By Whiskey three six in forum Trading Post
    Replies: 2
    Last Post: 02-20-2012, 03:17 AM
  2. Replies: 18
    Last Post: 05-01-2011, 10:31 AM
  3. Custom OD Green Factory XCR for sale
    By TerraShrewsbury in forum Trading Post
    Replies: 4
    Last Post: 10-05-2009, 05:12 PM
  4. Target specs for the XCR-M
    By tolson68 in forum .308 Winchester (7.62×51mm)
    Replies: 10
    Last Post: 07-05-2009, 11:05 AM
  5. Specs on 6.8 Barrels?
    By Welding Rod in forum General Discussion
    Replies: 2
    Last Post: 03-16-2008, 08:51 AM