XCR-M With custom 19" barrel - Page 3
Like Tree2Likes
Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 33

Thread: XCR-M With custom 19" barrel

  1. #21
    Rifleman RWSgunsmithing's Avatar
    Join Date
    Aug 2010
    Location
    Manning, IA
    Posts
    155

    Re: XCR-M With custom 19" barrel

    Nothing yet.


  2. #22
    Newbie VARMINTKILLER's Avatar
    Join Date
    Jan 2013
    Location
    S. IDAHO
    Posts
    25

    Re: XCR-M With custom 19" barrel

    Do you have a line on a 300 blackout barrel for my xcr-l? What barrels do you use? Thanks

  3. #23
    Rifleman RWSgunsmithing's Avatar
    Join Date
    Aug 2010
    Location
    Manning, IA
    Posts
    155

    Re: XCR-M With custom 19" barrel

    Probably won't do a black out as it's a picky case to begin with.

    I can get blanks from just about any manufacturer out there and have places that stock stuff as well.

  4. Remove Advertisements
    XCRForum.com
    Advertisements
     

  5. #24
    Rifleman AlaskaGuns's Avatar
    Join Date
    Feb 2012
    Posts
    115

    Re: XCR-M With custom 19" barrel

    Is there any way for you to make me a barrel without me sending you the gasblock/barrel from my XCR-M? I'm uncomfortable in being without it for more than a few days. If it's possible, I'd very much like to discuss having one made. Thanks!

  6. #25
    Rifleman RWSgunsmithing's Avatar
    Join Date
    Aug 2010
    Location
    Manning, IA
    Posts
    155

    Re: XCR-M With custom 19" barrel

    For me to do it properly I will.

    However I will at least need the bolt for headspace.

  7. #26
    Rifleman AlaskaGuns's Avatar
    Join Date
    Feb 2012
    Posts
    115

    Re: XCR-M With custom 19" barrel

    What state are you located in, and what's the turn-around time (Roughly). I'm clear up in Alaska.

  8. #27
    Rifleman RWSgunsmithing's Avatar
    Join Date
    Aug 2010
    Location
    Manning, IA
    Posts
    155

    Re: XCR-M With custom 19" barrel

    Iowa.

    Right now is not a good time as it's crazy busy here.

    I'll try and keep every one here updated.

  9. #28
    Newbie kanne54's Avatar
    Join Date
    Jan 2015
    Posts
    12
    Can you tell me what the weight difference might be between a 19" stainless barrel and the 18.6" heavy barrel is? My XCR-M is so front end heavy that if it made a worth while difference I'd go get a SS barrel tomorrow.
    Thanks

  10. #29
    XCR Guru fmunk's Avatar
    Join Date
    Nov 2010
    Location
    Kahleefonia
    Posts
    3,072
    IMO, heavy profile does not guarantee accuracy. It's a cheaper way to attempt it. Among the ARs I've had, some of the thinner profile examples yielded better performance than some heavies. The M&P 10 is a tapered profile and has shown better performance and weight at $1500. There is more to it than barrel profile with regards to accuracy (harmonics—and consistency of it—is a big factor)... As for weight, I don't think SS is going to make much difference in weight or balance.
    Last edited by fmunk; 02-10-2015 at 06:48 PM.
    Bravo likes this.
    Fool-proofing serves only one purpose: identify bigger fools.

  11. #30
    Newbie kanne54's Avatar
    Join Date
    Jan 2015
    Posts
    12
    The heavy Im shooting right now is very accurate no complaints on that side of things. The front end is just so heavy compared to my AR's its hard to hold steady for long periods. I guess a fluting job might be the way to go? Any thoughts on dropping some weight while maintaining the 18.6" barrel (non restricted status in Canada) This would be my go to rifle for everything if I could drop some weight. Was gonna replace the upper with the lighter keymod upper but its a $1000 and I dont have any takers on my current quad rail upper. Considering chopping a couple inches off the upper and machining off the rails and adding vent holes for $350. Anyway, open to any suggestions or experience anybody has.
    Thanks a lot,
    Kanne54

Page 3 of 4 FirstFirst 1234 LastLast

Sponsors

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Replies: 11
    Last Post: 12-03-2012, 12:36 PM
  2. Custom Barrel for XCR
    By borderghost in forum Other Accessories
    Replies: 1
    Last Post: 01-16-2012, 06:24 PM
  3. Replies: 5
    Last Post: 11-29-2011, 06:43 PM
  4. WTS: Custom 10.5" 5.56 Barrel SPF
    By AEnemaBay in forum Trading Post
    Replies: 3
    Last Post: 07-05-2011, 09:40 PM
  5. Need Ideas for custom barrel
    By JBiggs556 in forum General Discussion
    Replies: 11
    Last Post: 09-08-2010, 09:18 AM

Search tags for this page

5.56 custom 18 ss barrel suppressor
,
custom xcr barrel
,
stainless xcr target barrel
,

xcr custom barrel

,
xcr custom gun
,
xcr m
,
xcr m bolt
,
xcr m customized
,
xcr with custom
,
xcr-m
,
xcr-m barrel
,
xcr-m picture
Click on a term to search for related topics.